I'll show you how to clean gasoline chainsaws to keep them looking great and running like new. If your gas chainsaws are a mess or a little dirty, these tips will come in handy. Also find out how to fix one of them!

Before cleaning different types of gasoline saws, you must make sure that no force is applied to the tool. Otherwise, accidents may occur.

Before using any of the following gasoline chainsaws, follow these steps:

Chainsaws: Empty the fuel tank and disconnect the spark plug connector from the spark plug.

Step 1: Clean the tire

Locate the two nuts on the side cover of gasoline chainsaws to install the guide rod on the drive head, but do not unscrew them yet.

On some gasoline saws, it is impossible to remove the cover if the chain brake is locked. On some models, you can remove the cover, but putting it back will be problematic. Therefore, always disengage the chain brake before starting this work.

With the chain brake separated, loosen and remove the cover nut. Separate the guide rod and chain from the drive head. Set the chain aside.

If the guide rod is a little dirty, you can simply clean it with a cloth with detergent and water. If the stain is severe, a soluble degreaser may be needed to remove any build-up.

To clean the straight bar groove of gasoline chainsaws, you can use an exclusive groove cleaning tool or a scraper. Run the tool along the groove until there is no sticking between the tracks.

To clean the stem and chain lubrication hole (located at the bottom of the stem), use a pick or thin screwdriver to loosen any dirt that is blocking the hole. It is also helpful to use compressed air in these small areas. The guide rod may also have a hole near the tip of the blade to lubricate the gear. Clean it too.

Step 2: Clean the circuit

In a fully ventilated area, take a container and mix one cup of ammonia with one liter of water. Find a chainsaw chain in this mixture and leave it for 15 minutes. Wear a pair of thick, stretchy gloves to ensure safety. Meanwhile, use a fine-bristled brush to scrub each part of the chain until no debris remains.

After cleaning the chain, rinse it with water to remove the ammonia solution. Immediately after rinsing, dry the chain to remove all moisture. Fill a shallow pan with oil for your drumsticks and chain. Place the chain in oil and let it rest for three hours. After this, the chain is turned over and left for another three hours. Remove the chain from the board and touch it with a paper towel to remove any dripping oil. Also see how to replace a chainsaw chain.

Step 3: Cleaning the Motor Head

Wipe the outside of the drive head housing with a dry cloth. Use a gentle brush (1-2 inches wide) to remove dirt from around the crankcase, intake drum, and exposed bolts. If there is thick dirt stuck in these areas, use a pick or thin screwdriver to scrape it out.

Step 4: Clean the air filter (petrol models only)

On gasoline chainsaws, remove the top cover. Filter the air and cover the air intake with a cloth to prevent dust or debris from entering. Use a soft brush (1 to 2 inches wide) to remove dust accumulated on the air filter. If the air duct is excessively dirty, run it under water to remove stuck particles. Then let it dry before reconnecting it.

Step 5: Clean the spark plug (gas models only)

Once the top cover is removed, the spark plug can be accessed. Use a T-wrench or the wrench that comes with gas saws to unscrew and remove the spark plug. If the electrode is dark brown, there should be no problem. If they are black, broken or damaged, they should be replaced. Check your owner's manual for the correct spark plug part number.

Step 6: Clean the Radiator (Gas Models Only)

Remove the cap covering the radiator and rotor. Using a thin screwdriver, deftly scrape away any dirt that has accumulated between the cooling fins. Be careful as you don't want to damage the ribs. Use a fine brush (1-2 inches wide) to remove any debris that has accumulated in the yoke area.

Step 7: Assemble the Chainsaw

After cleaning the gasoline saws, reassemble them in reverse order.